ARCHITECTURAL SPECIFICATIONS

OVERHEAD COILING SHUTTERS

PART 1 - GENERAL

1.01 SUMMARY

1. Section includes exterior overhead Roll-Up storm and security shutters.

1.02 SUBMITTALS

1. Product Data: Submit manufacturer's complete product data for all specified components, including specifications, finish information and installation instructions.
2. Shop Drawings: Submit shop drawings showing layout, sizes and types, product materials, components and accessories, fabrication data, operation and wiring diagrams for motor driven operators, finishes, rough-in dimensions, anchorage and installation requirements and details.
3. Samples: Manufacturer's standard array of colors for selection by Architect.
4. Quality Assurance Submittals:
   1. Test Reports: Certified test reports showing compliance with specified requirements.
   2. Certificates: Manufacturer's certification that design criteria meets specified requirements.
   3. Operating and Maintenance Instructions: Submit detailed maintenance requirements and operating instructions.
   4. Warranty: Submit specified warranty documents.

1.03 QUALITY ASSURANCE

1. Installer Qualifications:
   1. Use only manufacturer's factory trained installers or qualified licensed installers approved by shutter manufacturer.
2. Regulatory Requirements:
   1. Comply with all local and governing code requirements.
   2. Unless required otherwise, fabricate to withstand wind loads that carry same rating as component and cladding of walls.
3. Pre-Installation Conference: Conduct a pre-installation meeting to verify project installation and coordination requirements, field conditions, and manufacturer instructions.

1.04 DELIVERY, STORAGE AND HANDLING

1. Deliver components in manufacturer's original, unopened, undamaged containers with identification labels intact. Store components protected from harmful weather conditions and damage from other construction activity.

1.05 PROJECT CONDITIONS

1. Field Measurements: Verify actual measurements of openings by field measurements before fabrication. Show recorded measurements on shop drawings.

1.06 WARRANTY

1. Manufacturer's Warranty: Submit, for Owner's acceptance, manufacturer's standard warranty document executed by an authorized company official.
   1. Warranty period: ______________years.

PART 2 - PRODUCTS

(Specifier Note: Typically in the following, where items occur in brackets ( ) select item desired for Project).

2.01 MANUFACTURER

1. Roll-a-way, Inc., 10601 Oak St. N.E.,
   St. Petersburg, FL 33716
   (727) 576-1143, (800) 683-9505,
   FAX (727) 579-9410

2.02 MATERIALS

1. Shutter Components:
   1. Slat Types:
      (Specifier Note: Select one of the material a. selections following).
      1. PVC Slats: Exterior type UV stabilized extruded polyvinyl chloride; Style: (System I, II curved P55). Color: (white) (ivory) (beige) (gray).
      2. Aluminum Foam-Filled Slats: Aluminum, 3005 H26 alloy, with polyurethane foam insulation core. (Mini aluminum AF150) (System I,II AF200). Color: (white) (ivory) (bronze) electrostatically applied paint.
      3. Aluminum Extruded Double Wall Slats: Aluminum, 6063-T6 alloy. Color: (beige) (white) (ivory) (bronze) electrostatically applied paint.
      4. Patented End Retention Extruded on PVC with Rebar Slats
   2. Bottom Slat: Extruded aluminum, 6063-T6 alloy, 0.050 inch wall thickness.
   3. Operation: (Manual) (Motor operated).
      1. Manual operator type: (Pull strap-coiler) (3/1 crank with strap-coiler) (Gear and crank handle).
         
         (Specifier Note: Select a. above or a. below to coordinate with selection of 3.above).
      2. Electric Motor operator type: Single phase 110V-60Hz, UL recognized. Motor Model / Size_______. Provide back-up battery power pack. Provide manual override capability allowing manual operation in case of power outage.
         
         (Specifier Note: Battery pack and manual override capability above are optional features, delete if not required).
   4. Side Frames: Die-cast aluminum, (4) (5) (6) sided.
   5. Box Cover (hood): Roll formed aluminum; .036 inch thickness, 3105-H14 alloy. (4) (5) (6) sided design.
   6. Track Guides: Aluminum extrusions; 6063-T6. Provide manufacturer's standard (System I track - 3 inch), (System I track - 3 inch, End retention System), (System II track - 2 1/2 inch), (System II ER - 2 1/2 inch)
   7. Mounting: (Jamb) (Surface) (Buildout).
   8. Purlin (stormbar) Assembly: Aluminum extrusions, 6005-T5 or 6063-T6 alloy. 3.0", 4.0" with or without I beam inserts, for fixed or removable application.
   9. Slat Hangers: Stainless steel spring design (Powder Coated).
   10. Reels: (Aluminum, 6063-T6 alloy - round & octogonal).
   11. Slat Reinforcement ReBAR: (Extruded aluminum, 6005-T5 alloy).

2.03 SHOP FINISH

1. Side Box Cover Frames and Track: (Electrostatically applied - ESP - paint finish AMAA 2603).
2. Color: (To match slats) (As selected by Architect).

PART 3 - EXECUTION

3.01 EXAMINATION

1. Verify conditions of substrates to determine if acceptable for shutter installation in accordance with manufacturer's instructions. Correct all unsatisfactory conditions prior to commencing shutter installations.

3.02 INSTALLATION

1. Install track and all shutter components to comply with project shop drawings and manufacturer's written installation requirements.
   1. Where metal surfaces are in contact with masonry, concrete or dissimilar metals, protect with manufacturer's recommended isolation coatings or tape.
2. After installation, lubricate, test and adjust shutters to operate properly and free from distortion.

3.03 CLEANING

1. Clean installed components in accordance with manufacturer's instructions prior to Owner's acceptance. Properly remove from the site all debris remaining from this installation.
2. Inadequate surface cleaning will result in corrosion formation & potential structural damage.

3.04 PROTECTION

1. Comply with manufacturer recommendations and protect completed shutter installations from damage during remaining construction so as not to void warranty.